Are you confused by the meaning of the charging error 8 message that your Roomba is displaying? Owners of Roombas frequently experience this problem, so in this article, we’ll explain what charging error 8 on your Roomba actually means. This message shows that the battery in your Roomba is not charging properly. We’ll examine the possible causes of this issue.
What is Roomba Charging Error 8?
A red-light ring and error message accompany the Roomba charging error 8, which might either be an operating or charging error. Operational error 8 happens when the motor cannot spin because the filter is clogged, which prevents dirt from being suctioned.
A malfunctioning charging dock is frequently at fault for the Charging Error 8 signal, which denotes a problem connecting the Roomba battery to the Lithium-Ion battery.
Older Roomba devices frequently experience this problem, but it can be fixed with straightforward troubleshooting.
The Virtual Wall accessory, which is intended to limit the motion of certain Roomba models, is also incompatible with certain of the newer versions, but the Dual Mode Virtual Wall and the Virtual Wall Lighthouse are compatible with older models.
What Causes Roomba Charging Error 8?
- Old or Dead Battery – An old or completely worn-out battery is the most frequent cause of Charging Error 8. Batteries for Roomba eliminates typically last about two years or 400 charging cycles. Your battery may not charge properly when it reaches the end of its useful life, requiring replacement.
- Non-Genuine Batteries – Using third-party, non-authentic batteries may result in this error. Such replacements are discouraged by iRobot, which also has software that can identify non-original batteries. To prevent charging problems, buying an original iRobot battery is a good idea.
- Faulty Battery – If your Roomba is relatively new and hasn’t been charged much, a defective battery may be the cause of your problems. In some situations, the manufacturer might offer a replacement under warranty.
- Dirty Charging Contacts – The charging of the Roomba or its charging dock can be affected by dust, rust, or filth on the metal contacts. The problem can be fixed by wiping these contacts with a moist cloth and making sure they are dry.
- Faulty Home Base – Charging Error 8 can also be brought on by a malfunctioning home base or charging dock. To identify the issue, try an alternative power lead and base.
- Extreme Temperature – Charging a Roomba in a location that is excessively hot or cold can make it more difficult to charge the batteries. Make sure the home base is located in the area with an appropriate climate.
- House Wiring Issues – Rarely, charging issues may be caused by issues with the electrical wiring of the house. Occasionally, the Roomba itself may have an unexpected system glitch that results in Charging Error 8.
How to Fix Roomba Error 8?
- Clean or Replace the Filter – The first step is to check and clean the filter located in the dustbin. Remove the dustbin from your Roomba and access the filter.
- Remove Dustbin Screws – Using a Phillips screwdriver, remove all screws from the top of the dustbin.
- Disengage the Lid – Carefully lift up the dustbin lid and remove the two plastic arms that connect it to the bin.
- Clean the Motor – Locate the vacuum motor (a circular object in the center of the dustbin) and remove any pet hair or debris that might be obstructing it. Use tweezers to clear any blockages.
- Use Canned Air – Spray canned air inside all parts of the vacuum motor and surrounding areas to ensure it’s clean and free of debris.
- Check the Fan – Attempt to manually spin the small black fan on the vacuum motor using tweezers. It should spin freely. If it doesn’t, the vacuum motor may need replacement.
- Reassemble the Dustbin – Reinsert the two small plastic arms and snap the lid back in place. Replace the screws and reinstall the filter in the dustbin.
- Reattach Dustbin – Place the cleaned and reassembled dustbin back into the Roomba and press the ‘CLEAN’ button to restart.
- Inspect the Charging Dock – Ensure that the charging dock is functioning correctly and making a proper connection with the Roomba. Clean the charging contacts on both the Roomba and the dock.
- Check Environmental Factors – Avoid charging the Roomba in extremely hot or cold environments, as this can affect the battery’s ability to charge.
- Replace the Battery – If the Roomba’s battery is old and doesn’t hold a charge, consider replacing it with a new, authentic iRobot battery.
- Contact iRobot Customer Care – If none of the above steps resolve the issue, and your Roomba is still under warranty, consider reaching out to iRobot Customer Care for further assistance or possible replacement of faulty components.
Will Resetting Fix Error 8 On Roomba?
The answer is yes. Restarting your Roomba will resolve charging error 8. Sometimes, faulty charging settings or firmware issues can cause this error.
While the robot is plugged into the charger, hold the spot/target and dock/home buttons simultaneously for 10 seconds to reset the Roomba. By doing this, the Roomba will be reset to its factory default settings, which might fix the issue and enable proper charging.
If your Roomba experiences error 8, resetting is a helpful troubleshooting option to take into consideration.
Why is Roomba Beeping Continuously During Charging?
A Roomba that continually beeps while charging may indicate a number of problems. Filters that are clogged, wheels that are stuck, chargers that aren’t working, a clogged trash can, error codes that are visible, out-of-date firmware, or faulty sensors are common culprits. For the issue to be properly addressed, the fundamental cause must be found.
The constant beeping problem can be fixed by cleaning filters, freeing stuck wheels, checking the charger, clearing clogs, updating software, or fixing sensor damage.
You can efficiently troubleshoot and resolve the beeping issue during the charging process by identifying the root of the problem.
How to Prevent Roomba Charging Error 8 in Future?
- Regular Maintenance – To avoid a blockage that may hinder charging, clean the dustbin and filter frequently.
- Connector Care – To keep the charging connectors clean and effective, periodically wipe them with a soft cloth and rubbing alcohol.
- Outlet Variation – Charge your Roomba in several outlets to ensure a steady flow of power and prevent any problems with a specific socket.
- Software Updates – Update the software on your Roomba regularly because new releases often arrive with problem fixes and improvements.
- Contact Support – If a problem continues, get in contact with iRobot customer service for help and possible fixes. They may provide detailed troubleshooting tips. These actions will assist in maintaining the functionality of your Roomba and lessen the possibility of experiencing charging error 8.
Watch this one,
Video Credits – scharajr